Side Billboard Contents

1. Model S-1 Side Billboard
 

 
2 Short Wheel-Well Straps w/
Clip & Hook, and 1 Long Strap
1 Safety Bungee Strap
2 Adjustable Legs w/
Suction Cups & Pins



 
2 Support Arms
2 Mushroom Locks
w/ Keys & Covers
2 Support Straps w/ Circular Spacers & 4 Screws

Installation
 Before installation, Drivertise recommends that you wax the area where the suction cups make contact. Repeat this process every two month for surface protection.
 
 
 Place both support straps under and around the roof rack.
The space between both straps should be approximately 14 inches apart. Tip: Once the straps are installed, for your convenience, you may leave them on while washing your vehicle.
Fasten by cranking upwards on the levers of the support strap. The support strap should fit tightly on your roof rack. Note: The strap may sit at a tight tilt. This is normal.
 
Take both straps, remove each screw from the inside of the cylinder with a screw-driver, and adjust the spacer to the lower position.
Place both straps under and around the roof rack. Tip: Once the straps are installed, for your convenience, you may leave them on while washing your vehicle
The space between both straps should be approximately 14 inches apart.
Fasten by cranking upwards on the levers of the support strap. The support strap should fit tightly on your roof rack.
1.  Insert the two support arms into the back panel of the billboard.
Billboard placement on drivers side
Twist arms clockwise into sockets labeled 2 and 4 until they fasten tightly into place at 90 degrees.
Billboard placement on passengers side
Twist arms clockwise into sockets labeled 1 and 3 until they fasten tightly into place at 90 degrees.
2. Installing the two support arms into the top row of the billboard will lower the height of the billboard from the top of the roof of your vehicle. Installing the support arms into the bottom row of the billboard, will increase the height of the billboard from the top of the roof of your vehicle.
3. Insert the two adjustable legs into the billboard. Attach one leg to each side of the billboard. You may adjust the legs by removing the pin and sliding it to the desired position, and then the pin to ensure that the adjustable legs lock into place.
4. You may adjust the legs by removing the pins and sliding them to the desired positions. Re-insert the pins to ensure that the adjustable legs lock into place. This function allows you to add spacing between the billboard and the surface of your vehicle.
5. Install the billboard onto the vehicle by aligning the support arm holes onto the round cylinder of the support straps. Note: Use the holes on the support arms that will allow the top of your billboard to stand as close to your vehicle as possible.
6. Make sure that the surface where the suction cups make contact with the body of the vehicle is flat and clean. Moisten the inside of the suction cups for a more secure grab.
7. Align the mushroom locks onto the round cylinder of the support straps.Snap in lock to secure your billboard.
8. Place the weather protective covers over the mushroom locks to protect from water damage.
9. Screw on security-screws through the thumb levers on both sides of the strap. This will prevent from the belt-strap releasing.
 
10. Attach the hooks onto the inside of the wheel-well, and fasten wheel-well straps tightly. If you need to adjust the straps to a tighter fit, un-clip the hooks, and slide the strap buckles upwards.
11. Note: A long strap is provided for vehicles that have a longer distance from the wheel-well to the bottom of the billboard. First, remove wheel-well hook from the short strap and attach it to the long strap. Then, attach the hook onto the inside of the wheel-well, and fasten wheel-well strap tightly.
12. For most vans and less contour vehicles, insert only the longer strap into the slot positioned towards the front of the vehicle. Attach the hooks onto the inside of the wheel-well and fasten straps tightly.
13. Wrap safety bungee around your roofrack, open the D-ring and clip onto the safety bungee.
14. Insert print. Open billboard door and slide print inside. Snap door shut. Important: Before driving, always make sure wheel-well straps, supports arms,support straps, suction cups, safety bungee and mushroom locks are properly secured.

Helpful Tips
If there is excess strap, tuck the excess strap underneath the roofrack to prevent from flapping due to wind
Once a week, You MUST wipe the surface where the suction cups touch your vehicle with a clean wet cloth. This scheduled cleaning will protect the surface of your vehicle.
To remove strap clips, press clips inwards from the back of the billboard to release.
On vehicles with vertical roof- racks, the billboard may block your fuel door. If this occurs, simply release the suction cups and release the strap hooks from the wheel-well and lift billboard very slightly outwards.
Replace your suction cups every 3 months to ensure a better suction.
The dimensions of your print ad measurements are 22'' x 33'' inches. Allow an extra 1'' inch blank margin for your vertical right border.